My Cart: 0 item(s)
EGW Red Dot Mount for the Docter, Burris Fastfire, Vortex Venom, and Vortex Viper for Colt 1911/22 Rail Gun (Walther Slide 22)
Mounting Hardware is Included
This mount fits:
- This mount is for a Colt Rail Gun 1911 .22lr that has the Walther slide.
Material: 7075 Aluminum
Coating: Matte Black Hardcoat
Overall Length: 1.811"
Overall Width: .99"
Torque Specs: 15 in/lbs
Red Dot Fitment:
- Vortex Viper
- Vortex Venom
- Burris FastFire
- Docter
- ADE RD3-001
- ADE RD3-002
- ADE RD3-009
- UTG Reflex Micro Dot
- Crimson Trace CTS-1200
- Crimson Trace CTS-1300
- Sightmark Mini Shot
- Sightmark Core Shot
The mounting screws require a 5/64" wrench and the set screws (when applicable) require a 1/16" wrench.
*All ADE mounts require 6-32 x 3/8" screws.
Please note: We have found that some red dots commonly found on Amazon such as the UTG and ADE may not hold the same tolerances as the red dots that this mount was initially created to work with. These dots may not fit properly on the posts on the plate. We would recommend either sending the red dot back for an exchange to whichever seller you purchased it from, or open up the holes in the bottom of the red dot to accommodate the pins.
Evolution Gun Works red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install.
Simply remove the rear sight on your gun and replace it with our mount in order to mount yourVortex Viper/Venom, Burris FastFire, or Docter red-dot sight. No alterations are required. You can take our mount off and replace your rear sight at any time. Mounting hardware included.
Installation Instructions
- Remove the rear sight*
- Install the EGW Sight Mount in the dovetail
- Tighten set screw (if applicable)
- Place the red dot sight on the EGW Sight Mount
(placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.)
- Apply blue Loctite to the provided mounting screws
- Torque mounting screws to 15in/lbs
2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights
2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights
The screws that are included with this mount require a 5/64'' allen wrench for installation.
Modification of your firearm may nullify the manufacturer's warranty.
This product should be installed and checked by a qualified gunsmith.
No liability is expressed or implied for damage or injury which may result from improper installation or use of this product.
1911 Quick Links
- 1911 accessories
- 1911 scope mount
- 1911 optic mount
- 1911 sights
- Bomar 1911 Red Dot Mount
- Bomar sights
- LPA 1911 Red Dot Mount
- LPA sights
- novak sights
- 1911 novak mounting plate
- novak 1911 sights
- 1911 novak red dot mount
- novak red dot mount
- 1911 red dot mount no drilling
- vortex venom 1911 mount
- vortex venom 1911 novak mount
- 1911 red dot mount novak
- 1911 red dot mount
- 1911 sight mount
- kimber 1911 red dot
- Rock iIland 1911 red dot mount
- magpul 1911 grips
- 1911 recoil buffer
- trijicon rmr novak dovetail mount for 1911
Vortex Venom Quick Links:
- Vortex Venom
- Vortex Venom for sale
- Vortex Venom glock mount
- Vortex Venom on ar15
- Vortex Venom picatinny mount
- Vortex red dot
- Venom red dot
- Vortex Venom on shotgun
- Vortex Venom red dot for sale
- Vortex Venom red dot
- Vortex Venom ar mount
- Vortex Venom offset mount
The distinction between inferior quality and premium Vortex Viper Mount undeniable. At MSP, we only offer Red Dot Mounts from the most trusted brands like Vortex Optics. Buy with confidence that we stand behind the product we sell.
WARNING: This product can expose you to Lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to - www.P65Warnings.ca.gov.
Customer Ratings & Reviews
Be the first to rate this item!
Write Review
