EGW Red Dot Mount for the Docter, Burris Fastfire, Vortex Venom, and Vortex Viper for Glock
Mounting Hardware is Included
This EGW Mount for Glock - for the Vortex Venom will fit all generation listed below:
- Glock 17
- Glock 19
- Glock 19x
- Glock 20
- Glock 21
- Glock 22
- Glock 23
- Glock 24
- Glock 26
- Glock 27
- Glock 29
- Glock 30
- Glock 30 SF
- Glock 31
- Glock 32
- Glock 33
- Glock 34
- Glock 35
- Glock 36 (Our mount is wider than the slide, but it will still work)
- Glock 37
- Glock 38
- Glock 39
- Glock 41
- Glock 42 (Our mount is wider than the slide, but it will still work)
- Glock 43 (Our mount is wider than the slide, but it will still work)
- Glock 43x (Our mount is wider than the slide, but it will still work)
- Glock 44
- Glock 45
- Glock 46
- Glock 48 (Our mount is wider than the slide, but it will still work)
- Canik TP9SF
- Bersa BP9CC
- Tactical Solutions .22lr Conversion
- Advantage Arms .22lr Conversion
Does not fit Glock MOS models.
- Glock 17 Gen 4 MOS
- Glock 19 Gen 4 MOS
- Glock 34 Gen 4 MOS
- Glock 35 Gen 4 MOS
- Glock 40 Gen 4 MOS
- Glock 41 Gen 4 MOS
- Glock 22 Gen 5 MOS
- Glock 23 Gen 5 MOS
- Glock 34 Gen 5 MOS
- Glock 45 MOS
- Glock 43x MOS
- Glock 48 MOS
Material: 7075 Aluminum
Coating: Matte Black Hardcoat
Overall Length: 1.811"
Overall Width: .99"
Mounting Hardware: (2) 6-32 Button Head Screws, (2) 6-32 Flat Head Screws, (1) 6-32 Set Screw
Red Dot Fitment: Vortex Viper/Venom, Burris FastFire, Crimson Trace CTS-1200, CTS-1300, Docter, ADE RD3-001*, ADE RD3-02*, ADE
The EGW Vortex Venom Glock Mount are meant to be installed from the left to the right. The dovetail has a progressive taper to allow for easier install.
Simply remove the rear sight on your gun and replace it with our mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. No alterations are required. You can take our mount off and replace your rear sight at any time. Mounting hardware included.
- Remove the rear sight*
- Install the EGW Sight Mount in the dovetail
- Tighten set screw (if applicable)
- Place the red dot sight on the EGW Sight Mount
(placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.)
- Apply blue Loctite to the provided mounting screws
- Torque mounting screws to 15in/lbs
2 Button Head Cap Screws - Provided for Vortex Viper and Vortex Venom Sights
2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights
The screws that are included with this mount require a 5/64'' allen wrench for installation.
Modification of your firearm may nullify the manufacturer's warranty.
This product should be installed and checked by a qualified gunsmith.
No liability is expressed or implied for damage or injury which may result from improper installation or use of this product.
The distinction between inferior quality and premium Vortex Viper Mount undeniable. At MSP, we only offer Red Dot Mounts from the most trusted brands like Vortex Optics. Buy with confidence that we stand behind the product we sell.
Customer Ratings & Reviews
Great red dot sight mount
Bought this Glock red dot sight mount before I jumped into having my slide milled out for red dot sight. Milling costs around 200-250 in my area, so before I committed to having this done, I wanted to be sure that moving to a red dot sight (Vortex Viper), this was the way I wanted to go. It's about 3/8ths of an inch higher (0ver the bore) than what the sight would be if you have your slide milled out, BUT you can get the idea of what a red dot is like, and you are only out the cost of this mount and your transparency in intact.
Amazing, SINGLE PIECE Vortex Venom Glock mount!
This Vortex Venom Glock mount is AMAZING! Single-piece, was definitely hard to get in, even with a sight pusher, and also has a set screw! This mount has about 400 rounds through it, and its still functioning flawlessly!
Venom dovetail mount
Great product that fit perfectly on my G17. A good alternative to machining the slide. Just added a taller front sight to help co-witness.
Takes some force to drive Glock red dot sight mount in
I didn’t have a lot of trouble mounting this on my Glock 35 slide. The dovetail is tight, and I had to use a brass punch to drive it in. Make sure to drive it from the left side to the right side. It is rock solid. I mounted a Vortex Venom to it quickly and sighted the pistol in. I have shot a few hundred rounds of .40 and 9mm through it and have not had to adjust the sight.
Perfect mount for Vortex viper red dot optic on a Glock 35
This vortex venom Glock mount is very tight and firm fit when installed. Some may find it difficult without the right tools, as it is designed as a press-fit installation. I imagine a regular sight pusher, even one that is Glock-specific will not work. Installed mine using an industrial-grade smooth-jawed vise to hold the slide. Started it into the dovetail with moderate taps with a rubber-tipped mallet when it would go no farther used 12oz hammer on a hardwood block until I had it centered on the slide — no damage to the finish of the mount. I've used EGW mounts on 2 CZ's and a Springfield 1911-A1 all fit ideally, but this Glock mount is exceptional in that you couldn't even see daylight between the slide and the mount on all mating surfaces. Very tight tolerances everywhere. Very pleased with this purchase.
Glock 43 vortex venom
It works great! Having a sight pusher made it easy to install, took a few minutes. Holds zero does not move at all on my Glock 43, vortex viper.
Vortex Venom mount for Glock
This vortex venom Glock mount os worth every bit money. Fits exceptionally tight in the dovetail. Admire the fact it's one piece. Set screw ensures it doesn't budge. No problems with 100 rounds through a Glock 26 with a vortex venom on top.
Best Glock red dot sight mount
Outstanding mounting platform for my Sightmark Mini-Shot. Exceptional dovetail fit and finish. Used the cheaper aluminum two-piece mount, and they failed in the first 50 rounds. Best to install with a sight pusher, very snug fit, which is excellent. Fired 400 shots and perfect performance.
Simple Glock red dot mount
Used this EGW Red dot part to mount a vortex viper on a Glock 19. It took some effort, but I was able to install without a sight pusher. I just used a hammer and a punch.
mount went on fairly easy. no one can tell what front sight will go with vortex venom. they say lines on sight are not sights but could use if sight went out. but need to know what screw head needed to use with screws with mount.