
EGW Red Dot Mount for the Docter, Burris Fastfire, Vortex Venom, and Vortex Viper for Bomar
Mounting Hardware is Included
This sight fits (including but not limited to):
- STI Edge (either this sight or LPA)
- Les Baer 1911 (adjustable rear sights)
- Colt Gold Cup Trophy with Bomar Rear Sight Cut
- Colt Gold Cup National Match .45acp
- Colt Gold Cup National Match 9mm
- Springfield TRP Operator
- Dan Wesson Bruin (may require fitting due to the Clark cut on the top of the slide)
Please verify the location of the elevation screw in your slide. The LPA has the elevation screw in the center of the dovetail cut. The Bomar has the elevation screw behind the dovetail cut.
Material: 7075 Aluminum
Coating: Matte Black Hardcoat
Overall Length: 1.811"
Overall Width: .99"
Torque Specs: 15 in/lbs
Red Dot Fitment:
- Vortex Viper
- Vortex Venom
- Burris FastFire
- Docter
- ADE RD3-001
- ADE RD3-002
- ADE RD3-009
- UTG Reflex Micro Dot
- Crimson Trace CTS-1200
- Crimson Trace CTS-1300
- Sightmark Mini Shot
The mounting screws require a 5/64" wrench and the set screws (when applicable) require a 1/16" wrench.
*All ADE mounts require 6-32 x 3/8" screws.
Please note: We have found that some red dots commonly found on Amazon such as the UTG and ADE may not hold the same tolerances as the red dots that this mount was initially created to work with. These dots may not fit properly on the posts on the plate. We would recommend either sending the red dot back for an exchange to whichever seller you purchased it from, or open up the holes in the bottom of the red dot to accommodate the pins.
Our red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install.
Simply remove the rear sight on your gun and replace it with our mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. You can take our mount off and replace your rear sight at any time. Mounting hardware included.
Installation Instructions
- Remove the rear sight*
- Install the EGW Sight Mount in the dovetail
- Tighten set screw (if applicable)
- Place the red dot sight on the EGW Sight Mount
(placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.)
- Apply blue Loctite to the provided mounting screws
- Torque mounting screws to 15in/lbs
2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights
2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights
The screws that are included with this mount require a 5/64'' allen wrench for installation.
Modification of your firearm may nullify the manufacturer's warranty.
This product should be installed and checked by a qualified gunsmith.
No liability is expressed or implied for damage or injury which may result from improper installation or use of this product.
Vortex Venom Quick Links:
- Vortex Venom
- Vortex Venom for sale
- Vortex Venom glock mount
- Vortex Venom on ar15
- Vortex Venom picatinny mount
- Vortex red dot
- Venom red dot
- Vortex Venom on shotgun
- Vortex Venom red dot for sale
- Vortex Venom red dot
- Vortex Venom ar mount
- Vortex Venom offset mount
Red Dot Mount Quick Links:
- egw red dot mount
- glock 43 red dot mount
- ak red dot mount
- dovetail red dot mount
- red dot mount
- offset red dot mount
- glock red dot mount
- ak47 red dot mount
- m&p shield red dot mount
- ak 47 red dot mount
- sig p320 red dot mount
- ruger mark iv red dot mount
- best glock dovetail red dot mount
- mossberg 500 red dot mount
- mossberg 590 red dot mount
- kimber 1911 red dot mount
- hk vp9 red dot mount
- glock red dot mount with iron sights
- carry handle red dot mount
- canik tp9sf red dot mount
- s&w 686 red dot mount
- cz p07 red dot mount
- sig p365 red dot mount
- 1911 novak red dot mount
- p320 red dot mount
- cz p10c red dot mount
- s&w revolver red dot mount
- revolver red dot mount
- red dot mount for ar15
- ar-15 red dot mount
- ar15 red dot mount
- ar red dot mount
The distinction between inferior quality and premium Vortex Venom Mount undeniable. At MSP, we only offer Red Dot Mounts from the most trusted brands like Vortex Optics. Buy with confidence that we stand behind the product we sell.
Customer Ratings & Reviews
- 1
Disappointed customer!
This mount will not fit into the BOMAR dovetail of a Ruger SR1911 10mm target model until, you remove so much material from the mount you're afraid it won't stay in placed because it doesn't have any way of holding it in place (set screw) other than friction. It is mounted but yet to shoot pistol with it and red dot sight. I just hope it doesn't drift off zero from improper fit.
- 1