Burris XTR Signature Tactical Rings 30mm

12

| Write a Review

Ratings Snapshot

5.0

out of 5

5 (12)

4 (0)

3 (0)

2 (0)

1 (0)

Would recommend this product.

100%

SKU: 126-BUR-XTR30MM
Manufacturer: Burris

I no longer use any other type of rings. These have a solid, heavy-duty construction that ensures the scope stays in place, even under the toughest recoil. So far, I have only tested them with 6.5 CM and 308, but I have no doubt they would perform well even with the recoil of a 50BMG. The best part is the included inserts, which allow you to extend your long-range capabilities without needing high MOA bases. I have a 20 MOA base, and by utilizing the proper insert placement, I can add another 10 MOA. This means my scope has an additional 45 MOA of range from center, allowing me to reach out to a mile with my scope.

I used these rings to mount a Vortex Viper 6.5-20x50 onto a enhanced RPR .308 rifle. Despite the high cost, I am very happy with my purchase. I was put off by the appearance of the large knob-style mounting screws on many of the cheaper options, so I went with these for their sleek look and superior grip. They are expertly crafted and enhance the appearance of my rifle. I am confident that they will provide reliable performance. The included carrying case is top-notch and provides a convenient place to store the included wrenches and spare inserts. If anyone would like to see pictures, I would be happy to share them.

To start with, these rings arrive in a top-notch case along with a comprehensive set of instructions. I considered using a ring alignment tool and lapping, but ultimately decided on this option as it is more cost-effective and easier to use, and also allows for future adjustments. So far, I have only done a preliminary bore sighting at 10 yards, simply by aligning the scope with the bore visually and making the necessary height adjustments. I plan to head to the range next to see if any further correction is needed for actual shot placement.

I am now a firm believer in these rings. Previously, I had two Sightmark Photon scopes that were consistently shooting low by 14 inches at 20 yards, despite attempts to adjust them with internal adjustments and other scope rings. However, after mounting these rings, I was able to find the right combination of adjustments, settling on a -20 at the front, which brought me within 2 inches of center. It was then easy to use the internal scope axis dial to line up perfectly. I cannot recommend these rings highly enough if you are facing any issues with lining up your shots. Additionally, they are well-made and of exceptional quality. A+ all around.

I mounted these onto a 30MOA base as I required a slight increase in cant, approximately 15 MOA, to utilize the full scope adjustment capabilities. My first attempts at shooting at a 50-yard distance resulted in shots that were approximately 12 inches to the right of the target, missing the paper completely. To resolve the issue, I loosened the front and rear base mounts and manually rotated the scope clockwise when viewed from above, not through the scope's tube. After that, I retightened the base screws and ensured they were tightened to the specified torque. The adjustment worked perfectly and I was able to zero in the scope without any further issues. I hope that the mounts do not loosen over time.

The Burris XTR Signature Rings offer excellent versatility and the ability to incorporate cant into your scope on your rifle. I installed them on a KIDD 10/22 receiver that had a 0 MOA picatinny milled in, and the scope I was using was a Vortex Diamondback Tactical 6-24x50. Without these rings, the scope adjustment was limited, leaving me with a misaligned scope barrel that required 4 additional MOA at 80 yards and beyond. However, the Burris XTR Signature Rings solved this problem, restoring the scope's adjustment to a level where I had ample UP and DOWN movement left in the scope. I highly recommend these rings to anyone looking for added adjustability and versatility in their scope mounting.

The Burris XTR Signature Rings are unparalleled in terms of stability and protection. They remain firmly in place, even under the most intense recoil, as long as the screws are properly torqued. You can be confident that they will not damage your scope in any way, and they offer a multitude of options for maximizing the click adjustments on your scope. Additionally, they provide full contact around the entire circumference of your scope, eliminating the need for lapping. While you could opt for a more expensive option, you will not find better scope rings than these.

The design of the product is impeccable. The addition of different shim sets provided the ideal balance for my 20 MOA rail. Without this, I would have lost 5 MOA on the upper part of my scope. This leveled the playing field and allowed me to get the most out of my shooting experience. While windage adjustment was not a major concern for me, elevation was a crucial aspect, and this product delivered in that regard. It was a breeze to install and took only half an hour of my time. I will be updating my review in the future to see how it handles the powerful recoil of my 257 Weatherby.

These scope rings are extremely sturdy and a great option if you don't want a one-piece mount. They can compete with rings that cost twice as much. I don't have many Burris optics, but if they're made like these rings, I may consider them. If you're looking for a reliable scope mount that won't drain your wallet, these rings are a great choice."

I previously used a Leupold Freedom Firedot 1.5-4 scope with a Leupold cantalever mount, but when I tried to level it, I found that it wasn't compatible with the leveling widget. I wanted to avoid cheap rings and knew that these guys produced high-quality gear, so I decided to try them out. Despite not being made in the USA, they had good reviews and a solid warranty. Installation was smooth, with no issues. What I like about these rings is that each one has six screws to secure the scope, which makes installation a lot easier, even though all six screws may not be necessary once it's in place. To get the right eye relief, I had to place the forward ring on my hand guard. It wasn't ideal, but the quality of the hand guard made it manageable. If the hand guard was of poor quality, I would have been more concerned.

I have a AK with a side scope rail that was riveted crooked. Ran out of elevation. No problem now. The quality of the Burris xtr signature rings 30mm excellent. The packaging is meant for storage. It’s realy a storage case. I will be buying a second set for my Spanish Mauser. Just installed a Scope rail mount and ran out of elevation with the scope that I wanted to use. Much easier than trying to shim.

Very nicely made.