EGW Dovetail Mount for the Trijicon RMR, Holosun 407c / 507c for S&W M&P
Mounting Hardware is Included
This mount will fit:
- Smith & Wesson M&P Full Size
- Smith & Wesson M&P 2.0 Full Size
- Smith & Wesson M&P 22 Full Size
- Smith & Wesson M&P Compact
- Smith & Wesson M&P 2.0 Compact
- Smith & Wesson SD9VE
- Smith & Wesson SD40VE
- Smith & Wesson M&P Shield
This mount does not fit:
- Smith & Wesson M&P C.O.R.E Series (Already optics ready)
- Smith & Wesson M&P Shield EZ .380
- Smith & Wesson M&P Shield EZ 9mm
- Smith & Wesson M&P .22 Compact
- Smith & Wesson SW9VE
- Smith & Wesson SW40VE
The hole for the set screw on this mount is drilled off-center intentionally. This is to allow the set screw to be tightened against the bottom of the dovetail cut in the slide. This creates an upward force on the dovetail of the mount. If the hole were cut in the center of the dovetail, the set screw would fall through the hole cut in the center of the slide which would render the set screw useless.
Smith and Wesson's rear sight dovetails are known to vary in dimensions. Our sights are made to the same tolerances. Some users may have trouble installing our plate on their slide due to the varying tolerances in your slides. Please keep this in mind when ordering. Our return policy does allow for returns of unused and undamaged parts. These mounts should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product.
Please note: Trijicon recommends the use of a sealing plate to prevent water from entering their red dots.
Material: 7075 Aluminum
Coating: Matte Black Hardcoat
Overall Length: 1.780
Overall Width: 1.1"
Mounting Hardware: (2) 6-32 Flat Head Screws, (1) 6-32 X 3/16 Set Screw
Red Dot Fitment:
- Trijicon RMR
- RMR for sale
- Trijicon SRO
- Holosun HE407C
- Holosun HE507C
- Holosun HS407C
- Holosun HS507C
- Swampfox Kingslayer
- Swampfox Liberty
- Swampfox Justice
Our red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install.
Simply remove the rear sight on your gun and replace it with our mount in order to mount your Trijicon RMR red dot sight. You can take our mount off and replace your rear sight at any time. Mounting hardware included.
Installation Instructions
- Remove the rear sight*
- Install the EGW Sight Mount in the dovetail
- Tighten set screw (if applicable)
- Place the red dot sight on the EGW Sight Mount
(placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.)
- Apply blue Loctite to the provided mounting screws
- Torque mounting screws to 15in/lbs
*Rear sight pusher tool highly recommended*
Trijicon Quick links
Red Dot Mount Quick Links:
- egw red dot mount
- glock 43 red dot mount
- ak red dot mount
- dovetail red dot mount
- red dot mount
- offset red dot mount
- glock red dot mount
- ak47 red dot mount
- m&p shield red dot mount
- ak 47 red dot mount
- sig p320 red dot mount
- ruger mark iv red dot mount
- best glock dovetail red dot mount
- mossberg 500 red dot mount
- mossberg 590 red dot mount
- kimber 1911 red dot mount
- hk vp9 red dot mount
- glock red dot mount with iron sights
- carry handle red dot mount
- canik tp9sf red dot mount
- s&w 686 red dot mount
- cz p07 red dot mount
- sig p365 red dot mount
- 1911 novak red dot mount
- p320 red dot mount
- cz p10c red dot mount
- s&w revolver red dot mount
- revolver red dot mount
- red dot mount for ar15
- ar-15 red dot mount
- ar15 red dot mount
- ar red dot mount
M&P Quick Links:
- m&p 2.0 accessories
- smith and wesson m&p 40 accessories
- m&p 40 accessories
- m&p 45 accessories
- m&p 45 upgrades
- m&p shield red dot mount
- m&p shield 9mm accessories
- m&p shield plus accessories
- m&p shield 9mm upgrades
- m&p shield accessories
- m&p shield plus upgrades
- s&w shield 40 accessories
The distinction between inferior quality and premium RMR Mount undeniable. At MSP, we only offer Mounts from the most trusted brands like trijicon. Buy with confidence that we stand behind the product we sell.
Customer Ratings & Reviews
- 1
This mount works
Arrived in a timely fashion. Actually fit the gun unlike my previous purchase someplace else for an adaptor that comes in 2 pieces. This fits tight. If you have a site pusher make sure that the notch is wide enough for this plate or you will be pounding it into the dovetail as I did. I've yet to shoot the pistol with the new site attached but I have no doubts that the adaptor plate will NOT move.
EGW Mount
Very well made, precision machined mount. Easy to install with minimal tools all mounting points and screw holes were exact for the sight I used.
M&P SD9VE Trijicon RMR mount
Used this to mount a RMR on a M&P SD9VE. It took some effort but I was able to mount without a sight pusher. Just used a hammer and a punch.
- 1