Weaver 4 Hole Skeleton Scope Rings - 30mm

12

| Write a Review

Ratings Snapshot

5.0

out of 5

5 (12)

4 (0)

3 (0)

2 (0)

1 (0)

Would recommend this product.

100%

SKU: 105-WVR-4836X
Manufacturer: Weaver

Outstanding quality! These rings were designed for a 30mm tube with a 50mm objective lens and mounted on a 20 MOA base, resulting in a perfect height. Keep in mind that if you plan to use low rings for a 1" tube with a 50mm objective lens, you must use medium rings, as low rings will not fit. Combining low rings with a 30mm tube and 50mm objective lens does not guarantee compatibility with 1" tubes. Thanks!

I have a long history of using Weaver products, both professionally and personally, spanning over 40 years. As with any scope mounting system, it's important to inspect it before use. Some may require lapping, while others will fit seamlessly. The rings I bought needed a small fix - cleaning up one of the bottom saddles - which I achieved with a light sanding using fine sandpaper. It took only a few minutes to resolve the issue. I would definitely buy these rings again."

The Vortex Diamondback 6-24x50 scope has been successfully mounted on my Savage 110 Tactical rifle. I used lock tight on all screws for added security. The fit feels solid, with a small amount of space remaining between the scope bell and barrel. I will update this post if any issues arise after shooting.

You can't beat these weaver skeleton rings for the price. Shipped right away along with my Nikon Coyote Special 4x12x40 scope, and all was intact! I heard OP was a great place to buy about anything hunting--now I know!

Rings are well machined and fit in my AR with no problems. I would repurchase it. The taller height is excellent for scopes with large diameter bells and worked with my compact scope. I was a little worried because of the four lug mount that it would not fit between bells, but it fit just right.

Lite weight and more than adequate.

These rings have the same Weaver quality as their other products. They are durable and sturdy, and the tip-off feature allows me to swap scopes quickly and still maintain nearly perfect zero. The "skeleton" style also looks very sharp. These have been very hard to find.

Used these 30mm scope rings to mount a Leupold VXR scope on my Ruger 10/22 TD. They are low profile, nice looking, and strong. Weaver recommends only 12-15 inch-pounds of torque on the cap screws. I have a Wheeler F.A.T. wrench(torque wrench), so that was no problem. I used to over tighten everything and have stripped more than one machine screw!

These weaver skeleton rings give an excellent grip for mounting scopes on 1913 Picatinny & Weaver style rails while adding very minimum weight to the rifle. No rough edges or inconsistencies.

Due to the size of the optics purchased, these Weaver Skeleton Scope Rings are exactly what was needed to install my new scope on the flattop rail of my AR-15 — used in conjunction with the quick-release Picatinny rail, the optics clear the top of the gun barrel with plenty of room. The four-hole design gives plenty of bases to stabilize the scope and provide the proper level and balance. Just an FYI: Use a crisis/cross tightening pattern while every now and then looking through the scope to make sure the scope stays level. If you tighten down on one side, then go to other the scope with coming off level on you.

These scope rings are precisely what was needed to mount my new scope on the flattop rail of my AR-15 — used in combination with the quick release Picatinny rail, the optics clear the top of the gun barrel with plenty of room. The four hole design provides lots of bases to support the scope and provide the proper level and balance. Just an FYI: Use a crisis/cross screwing pattern while looking through the scope to make sure the scope stays level. If you squeeze down on one side, then go to other the scope with coming off level on you.

good products and very low price