EGW Dovetail Mount for the Docter, Burris Fastfire, Vortex Venom & Viper for Ruger Auto

9

| Write a Review

Ratings Snapshot

4.9

out of 5

5 (8)

4 (1)

3 (0)

2 (0)

1 (0)

Would recommend this product.

100%

SKU: 198-493-21
UPC: 841370112951
Manufacturer: EGW - Evolution Gun Works
MFG#: EGW 49321

EGW Red Dot Mount for the Docter, Burris Fastfire, Vortex Venom, and Vortex Viper for Ruger Auto (Mk 1, Mk 2, Mk 3, Mk 4, P85, P90)

Mounting Hardware is Included

This mount fits:

• Ruger MK I (Ruger Mark I)
• Ruger MK II (Ruger Mark II)
• Ruger MK III (Ruger Mark III)
• Ruger MK IV (Ruger Mark IV)
• Ruger P85
• Ruger P89
• Ruger P90-95
• Ruger P97
• Ruger 22/45

Material: 7075 Aluminum
Coating: Matte Black Hardcoat
Overall Length: 1.811"
Overall Width: .99"
Mounting Hardware: (2) 6-32 Button Head Screws, (2) 6-32 Flat Head Screws, (2) 6-32 Set Screw

Red Dot Fitment:

• Vortex Viper
• Vortex Venom
• Burris FastFire 1, 2, 3, 4
• Docter
• ADE RD3-001
• ADE RD3-002
• ADE RD3-009
• UTG Reflex Micro Dot
• Crimson Trace CTS-1200
• Crimson Trace CTS-1300
• Sightmark Mini Shot
• Sightmark Core Shot

The mounting screws require a 5/64" wrench and the set screws (when applicable) require a 1/16" wrench.

*All ADE mounts require 6-32 x 3/8" screws.

Please note: We have found that some red dots commonly found on Amazon such as the UTG and ADE may not hold the same tolerances as the red dots that this mount was initially created to work with. These dots may not fit properly on the posts on the plate. We would recommend either sending the red dot back for an exchange to whichever seller you purchased it from, or open up the holes in the bottom of the red dot to accommodate the pins.

EGW red dot mounts red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install.

Simply remove the rear sight on your gun and replace it with our mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. You can take our mount off and replace your rear sight at any time. Mounting hardware included.

Installation Instructions
- Remove the rear sight*
- Install the EGW Sight Mount in the dovetail
- Tighten set screw (if applicable)
- Place the red dot sight on the EGW Sight Mount
(placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.)
- Apply blue Loctite to the provided mounting screws
- Torque mounting screws to 15in/lbs

2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights
2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights

The screws that are included with this mount require a 5/64'' allen wrench for installation.

Modification of your firearm may nullify the manufacturer's warranty.
This product should be installed and checked by a qualified gunsmith.
No liability is expressed or implied for damage or injury which may result from improper installation or use of this product.

Alt Description:

• Ruger 22/45 red dot mount
• Ruger Mark IV optic mount
• Ruger Mark I Vortex Venom Mount
• Ruger Mark II Vortex Venom Mount
• Ruger Mark III Vortex Venom Mount
• Ruger Mark IV Vortex Venom Mount
• Ruger Mark I Red Dot Mount
• Ruger Mark II Red Dot Mount
• Ruger Mark III Red Dot Mount
• Ruger Mark IV Red Dot Mount
• Vortex Venom Ruger mark iv
• Ruger mark iv dovetail mount
• ruger mk iv red dot mount
• 22/45 red dot mount
• Ruger mark 4 red dot mount
• red dot for ruger mark iv
• ruger mk4 red dot mount
• ruger mark ii red dot mount
• Ruger mark iv with red dot

Quick Links:

• Ruger Mark I Accessories
• Ruger Mark II Accessories
• Ruger Mark III Accessories
• Ruger Mark IV Accessories

The distinction between inferior quality and premium scope mount is undeniable. At MSP, we only offer Ruger mark iii accessories from the most trusted brands like Evolution Gun Works. Buy with confidence that we stand behind the product we sell.