EGW Red Dot Mount for the Docter, Burris Fastfire, Vortex Venom, and Vortex Viper for Smith & Wesson M&P
Material: 7075 Aluminum
Coating: Matte Black Hardcoat
Overall Length: 1.811"
Overall Width: .99"
Mounting Hardware: (2) 6-32 Button Head Screws, (2) 6-32 Flat Head Screws, (1) 6-32 Set Screw
Red Dot Fitment: Vortex Viper/Venom, Burris FastFire, Shield RMS, Docter
This Evolution Gun Works - EGW M&P Red Dot Mount will fit:
- Smith & Wesson M&P Full Size
- Smith & Wesson M&P 2.0 Full Size
- Smith & Wesson M&P 22 Full Size
- Smith & Wesson M&P Compact*
- Smith & Wesson M&P 2.0 Compact*
- Smith & Wesson SD9VE
- Smith & Wesson SD40VE
This Evolution Gun Works (EGW) M&P Red Dot Mount does NOT fit:
- Smith & Wesson M&P Shield (Our mount is too wide to fit the Shield)
- Smith & Wesson SW9VE
- Smith & Wesson SW40VE
- Smith & Wesson M&P C.O.R.E Series
*Will not fit the M&P .22 Compact.
Smith and Wesson's rear sight dovetails are known to vary in dimensions. Our sights are made to the same tolerances. Some users may have trouble installing our plate on their slide due to the varying tolerances in your slides. Please keep this in mind when ordering. Our return policy does allow for returns of unused and undamaged parts. These mounts should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product.
Our red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install.
Simply remove the rear sight on your gun and replace it with our mount in order to mount your Leupold DeltaPoint Pro, JPoint, Redfield Accelerator, or Optima red-dot sight. No alterations are required. You can take our mount off and replace your rear sight at any time. Mounting hardware included.
Remove the rear sight*
Install the EGW Sight Mount in the dovetail
Tighten set screw (if applicable)
Place the red dot sight on the EGW Sight Mount
(placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.)
Apply blue Loctite to the provided mounting screws
Torque mounting screws to 15in/lbs
*Rear sight pusher tool highly recommended*
2 Button Head Cap Screws - Provided for Vortex Viper and Vortex Venom Sights
2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights
The screws that are included with this mount require a 5/64'' allen wrench for installation.
Modification of your firearm may nullify the manufacturer's warranty.
This product should be installed and checked by a qualified gunsmith.
No liability is expressed or implied for damage or injury which may result from improper installation or use of this product.
- m&p 2.0 red dot sight mount
- smith and wesson m&p 2.0 red dot mount
- smith & wesson m&p red dot mount
- red dot for m&p 2.0 compact
The distinction between inferior quality and premium Fastfire mount or Vortex Venom Mount undeniable. At MSP, we only offer Mounts from the most trusted brands like EGW. Buy with confidence that we stand behind the product we sell.
Customer Ratings & Reviews
Excellent solution M&P 2.0 red dot sight mount
I loved the ease of installation — a much better option than having my slide milled to accept the vortex sight.
AMAZING Vortex venom m&p mount
This Vortex venom m&p mount is AMAZING! Single piece was hard to get in, even with a sight pusher, and also has a set screw! This mount has about 400 rounds through it, and its still functioning flawlessly!
m&p red dot sight mount
There was no issue mounting this red dot mount on my M&P Pro slide. The dovetail is tight, and I had to use a brass punch to drive it in. Make sure to drive it from the left side to the right side. It is rock solid. I mounted a Vortex Venom to it promptly and sighted the pistol in. I have shot a few hundred rounds of .40 and 9mm through it and have not had to adjust the sight.
M&P 2.0 red dot sight mount fits Like a Glove.
It's helpful to know there are companies still willing and able to manufacture small, somewhat obscure parts that are still nevertheless considered very important to someone's firearm upgrades. The Evolution Gun Works M&P 2.0 red dot sight mount purchased from MSP allowed me to finish the mini red-dot installation on my Smith & Wesson M&P pistol almost effortlessly.
EGW Sight Mount for Vortex Venom On S&W M&P.
Very pleased and it works great. I ordered a second one for my back-up gun.
Had a difficult time finding a Viper mount for my M&P 2.0. This mount is the ticket! It is stable and fits in extremely snug. Happy to have this mount
EGW Sight Mount for Vortex Venom On S&W M&P.
The mount works just as advertised. No problems whatsoever. Will probably get another one for another M&P I have and the service was great.