L&M Single Ring Shotgun Magazine Tube Light Mount

34

| Write a Review

Ratings Snapshot

4.6

out of 5

5 (22)

4 (11)

3 (0)

2 (1)

1 (0)

Would recommend this product.

97.1%

SKU: 123-LMS-LM
Manufacturer: L&M

Strong, well made. Allows light to be mounted high enough and if back enough of rear sight, will assist in illuminating front sight. Also depending on the length of your light and considering mounting it far back enough to illuminate front sight, you may have to alter your forend to allow clearance. In my case on the 870 pump.

This product is perfect for attaching a tactical light to a 870 Remington Defender or model 1300 Mossberg. High quality. Removable

Just after ordering a Mossberg flashlight mount I realised there was a special mount made just for the 590A1. I immediately emailed MSP. I never received a response, just a shipping notification. Upon delivery I found the standard Mossberg mount was shipped, days after my email. To this day I still haven't received a response. Went ahead and bought the correct mount. Now both my 500 & 590A1 have mounts. Unless absolutely needed I wouldn't buy from MSP again. God forbid a mount breaks.

This is an excellent product! It would have been eaiser if there were instructions, but it didn't take long to figure out. May not work with all 1" flashlights, depending on the size of the head. I found the perfect light and my 870 tactical is now just right!

This is a good, solid mount. The only gripe I have with it on my M4 is that every time I want to remove the barrel to clean it, this must come off too. That means first I remove the flashlight, only then can I take the mount off. Kind of a pain. Still on my search for the perfect Benelli M4 light mount...

I used the mount to attach a Quark Maelstrom X7,(Highly Recommended!) to a 12 gauge Winchester 1300 Defender in the 9 o'clock position near the end of the barrel. The light mounted nice and close to the barrel and feed tube and with a little blue thread lock I have had no problems after a few boxes of assorted loads at the range. I could not be happier! I would like to share that this light because of it's design may not work on your weapon light if the barrel diameter is over one inch or has obstructions that would prevent you from sliding the light in place in the single ring mount hole after your removed you emitter head or tail cap.

Mounted a Surefire flashlight onto a Winchester 1300 XTR with a Choate magazine extension. Slick hardware, professionally made, fits very well, and is easy to adjust.

I bought a 26mm mount cause it was the largest they had. But I had a nordic magazine tube that was 27mm for my m2. So when I got the mount I had to mill out another 1mm plus .005 for clearance to make it slide on the tube. Works great! Just wish they made one for the nordic tubes

Possibly the BEST tactical light mount I have ever used. Solid, Fits tight to the gun, Puts the Polytac light in an absolute perfect position. Have yet to find a better mount made anywhere by another company.

Awesome product and awesome service! Recommend product and everyone here!

The mount is just what I was lookiing for. Fits tight to the weapon with minimal interference if you use it for a car/truck weapon i.e. snagging on seat covers etc. Although it is a bit pricey in my opinion, the quality and finish is good. I have searched and bought multiple light mounts before springing for this one and it's by far superior to the other bulky mounts.

i looked all over for a light mount that wasn't too over engineered. first off it looks great. nice fit & finish. very beefy. simple as pie to mount up. 5 minutes tops. best of all, you don't have to remove it to take off your barrel for cleanings. i use a mossy 500 w/ a fenix flashlight. great product for those looking for a system that gets to the point. no fuss or fancy gadgets to deal with when your trying to protect your family & home.