
EGW Red Dot Mount for the Docter, Burris Fastfire, Vortex Venom, and Vortex Viper for Smith & Wesson Revolver
This Evolution Gun Works - EGW mounts was designed to fit :
- Smith & Wesson K Frame Revolvers
- Smith & Wesson L Frame Revolvers
- Smith & Wesson N Frame Revolvers
- Smith & Wesson X Frame Revolvers
If your revolver is not drilled and tapped this mount will not work. The best way to verify that it is/is not drilled and tapped is to open the cylinder and check the rib underneath. There should be through holes that are drilled and tapped. If there are not (like the above image) this mount will not work without you having the gun drilled and tapped. You can have a competent and qualified gunsmith drill and tap the top strap with the standard S&W hole pattern which will allow you to use our mount.
Material: 7075 Aluminum
Coating: Matte Black Hardcoat
Overall Length: 1.811"
Overall Width: .99"
Mounting Hardware: (2) 6-32 Button Head Screws, (2) 6-32 Flat Head Screws, (1) 6-48 Torx Head Screw
Red Dot Fitment:
- Vortex Viper
- Vortex Venom
- Burris FastFire
- Docter
- ADE RD3-001
- ADE RD3-002
- ADE RD3-009
- UTG Reflex Micro Dot
- Crimson Trace CTS-1200
- Crimson Trace CTS-1300
- Sightmark Mini Shot
*All ADE mounts require 6-32 x 3/8" screws.
Please note: We have found that some red dots commonly found on Amazon such as the UTG and ADE may not hold the same tolerances as the red dots that this mount was initially created to work with. These dots may not fit properly on the posts on the plate. We would recommend either sending the red dot back for an exchange to whichever seller you purchased it from, or open up the holes in the bottom of the red dot to accommodate the pins.
EGW red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install.
Simply remove the rear sight on your gun and replace it with our mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. You can take our mount off and replace your rear sight at any time. Mounting hardware included.
Installation Instructions
- Remove the rear sight*
- Install the EGW Sight Mount in the dovetail
- Tighten set screw (if applicable)
- Place the red dot sight on the EGW Sight Mount
(placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.)
- Apply blue Loctite to the provided mounting screws
- Torque mounting screws to 15in/lbs
2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights
2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights
The screws that are included with this mount require a 5/64'' allen wrench for installation.
K-frame (medium) models
- S&W 10 Police Vortex Viper Red Dot Mount
- S&W 11 Vortex Viper Red Dot Mount
- S&W 12 Vortex Viper Red Dot Mount
- S&W 13 Vortex Viper Red Dot Mount
- S&W 14 Vortex Viper Red Dot Mount
- S&W 15 Vortex Viper Red Dot Mount
- S&W 16 Vortex Viper Red Dot Mount
- S&W 17 Vortex Viper Red Dot Mount
- S&W 18 Vortex Viper Red Dot Mount
- S&W 19 Vortex Viper Red Dot Mount
- S&W 48 Vortex Viper Red Dot Mount
- S&W 53 Vortex Viper Red Dot Mount
- S&W 64 Vortex Viper Red Dot Mount
- S&W 65 Vortex Viper Red Dot Mount
- S&W 66 Vortex Viper Red Dot Mount
- S&W 67 Vortex Viper Red Dot Mount
- S&W 68 Vortex Viper Red Dot Mount
- S&W 617 Vortex Viper Red Dot Mount
L-frame (medium-large) models
- S&W 386 Vortex Viper Red Dot Mount
- S&W 586 Vortex Viper Red Dot Mount
- S&W 686 Vortex Viper Red Dot Mount
- S&W 686+ Vortex Viper Red Dot Mount
- S&W 619 Vortex Viper Red Dot Mount
- S&W 620 Vortex Viper Red Dot Mount
- S&W 646 Vortex Viper Red Dot Mount
- S&W 69 Vortex Viper Red Dot Mount
N-frame (large) models (formerly S-frame)
- S&W 29s Vortex Viper Red Dot Mount
- S&W 1917 Vortex Viper Red Dot Mount
- S&W 22 Vortex Viper Red Dot Mount
- S&W 24 Vortex Viper Red Dot Mount
- S&W 25 Vortex Viper Red Dot Mount
- S&W 27 Vortex Viper Red Dot Mount
- S&W 28 Vortex Viper Red Dot Mount
- S&W 29 Vortex Viper Red Dot Mount
- S&W 57 Vortex Viper Red Dot Mount
- S&W 58 Vortex Viper Red Dot Mount
- S&W 610 Vortex Viper Red Dot Mount
- S&W 625 Vortex Viper Red Dot Mount
- S&W 627 Vortex Viper Red Dot Mount
- S&W 629 Vortex Viper Red Dot Mount
X-frame models
- S&W 500 Vortex Viper Red Dot Mount
- S&W 460XVR[46] Vortex Viper Red Dot Mount
Vortex Venom Quick Links:
- Vortex Venom
- Vortex Venom for sale
- Vortex Venom glock mount
- Vortex Venom on ar15
- Vortex Venom picatinny mount
- Vortex red dot
- Venom red dot
- Vortex Venom on shotgun
- Vortex Venom red dot for sale
- Vortex Venom red dot
- Vortex Venom ar mount
- Vortex Venom offset mount
The distinction between inferior quality and premium Vortex Viper Mount undeniable. At MSP, we only offer Red Dot Mounts from the most trusted brands like Vortex Optics. Buy with confidence that we stand behind the product we sell.
Customer Ratings & Reviews
- 1
vortex venom on s&w 686
Great optic mount. Wry easy to install on my S&W 686 rear sight. I still have it five stars even though I wished it came with a rubber gasket underneath the red dot and the mount. But other than that, the red dot was so simple to assemble and sighting it with my gun.
- 1