EGW Viper/Venom Sig Sauer P210 Standard, P220-229, P320 Red Dot Mount (fits Burris FastFire and Docter)
THIS MOUNT DOES NOT WORK WITH ANY SIG OPTICS READY PISTOLS (P320 X-CARRY ETC.)
Material: 7075 Aluminum
Coating: Matte Black Hardcoat
Overall Length: 1.811"
Overall Width: .99"
Mounting Hardware: (2) 6-32 Button Head Screws, (2) 6-32 Flat Head Screws, (1) 6-32 Set Screw
Red Dot Fitment: Vortex Viper/Venom, Burris FastFire, Crimson Trace CTS-1200, CTS-1300, Docter, ADE RD3-001*, ADE RD3-02*, ADE RD3-009*
*All ADE mounts require 6-32 x 3/8" screws.
This Evolution Gun Works - EGW SIG P320 Red Dot Mount fits (including but not limited to):
- Sig #8 Sights
- P210 Standard
- P226 red dot mount
- P320 red dot mount
- Bersa Thunder UC Series (9/40/45)
- Bersa Thunder HC Series (9/40/45)
- FN 509
This Evolution Gun Works - EGW SIG P320 Vortex Venom Mount does NOT fit:
- Sig 1911s
- Any Optics Ready Sigs i.e. P226 Legion RX, P229 RX, P320 X-Carry etc.
- P210 Target
- P365 (The dovetail cut is too deep to work with our mount)
- FN 509 Tactical
The EGW SIG P320 red dot mount is meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install.
Simply remove the rear sight on your gun and replace it with our mount in order to mount yourVortex Viper/Venom, Burris FastFire, or Docter red-dot sight. No alterations are required. You can take our mount off and replace your rear sight at any time. Mounting hardware included.
EGW SIG P320 Red Dot Mount Installation Instructions
- Remove the rear sight*
- Install the EGW Sight Mount in the dovetail
- Tighten set screw (if applicable)
- Place the red dot sight on the EGW Sight Mount
(placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.)
- Apply blue Loctite to the provided mounting screws
- Torque mounting screws to 15in/lbs
2 Button Head Cap Screws - Provided for Vortex Viper and Vortex Venom Sights
2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights
The screws that are included with this mount require a 5/64'' allen wrench for installation.
Modification of your firearm may nullify the manufacturer's warranty.
This product should be installed and checked by a qualified gunsmith.
No liability is expressed or implied for damage or injury which may result from improper installation or use of this product.
The distinction between inferior quality and premium Vortex Venom Mount undeniable. At MSP, we only offer mounts from the most trusted brands like Vortex Optics. Buy with confidence that we stand behind the product we sell.
Customer Ratings & Reviews
sig p220 red dot mount
Pushed it right into place on my Sig p220. It went in about 75% of the way with a gunsmith brass mallet. The last 5% was tight, but the pusher tool got it perfectly centered. Follow the taper on your sight rails. Mine tapered from left to right.
Sig p226 red dot mount
I didn’t have a lot of trouble mounting this on my Sig p226 35 slide. The dovetail is tight, and I had to use a brass punch to drive it in. Make sure to drive it from the left side to the right side. It is rock solid. I mounted a Vortex Venom to it easily and sighted the pistol in. I have shot a few hundred rounds of through it and have not had to adjust the sight.
Sig p320 vortex venom mount
It works! Having a sight pusher made it easy to install, took a few minutes. Holds zero does not move at all on my Sig p320, vortex viper.
Sig p320 dovetail mount
Every bit worth money. Fits extremely tight in the dovetail. Love the fact it's one piece. Set screw ensures it doesn't move. No issues with 100 rounds through a Sig p320 with a vortex venom on top.