EGW Red Dot Mount for Vortex Venom/ Viper for Remington / Para 10mm Long Slide
Not Yet Rated | Write the First Review SKU: 198-49294

EGW Red Dot Mount for the Docter, Burris Fastfire, Vortex Venom, and Vortex Viper for Remington / Para 10mm Long Slide

This mount fits:

• Remington R1 10mm Hunter with adjustable rear sight
• Para Elite RS 10mm Hunter with adjustable rear sight

This mount is based off of an LPA mount, but shortened to fit on the Remington and Para Long Slide.

*All ADE mounts require 6-32 x 3/8" screws.

Material: 7075 Aluminum
Coating: Matte Black Hardcoat
Overall Length: 1.811"
Overall Width: .99"
Torque Specs: 15 in/lbs

Mounting Hardware:
(2) 6-32 Button Head Screws
(2) 6-32 Flat Head Screws
(1) 6-32 Set Screw

Red Dot Fitment:

• Vortex Viper
• Vortex Venom
• Burris FastFire
  • Burris FastFire 2
    • Burris FastFire II
  • Burris FastFire 3
    • Burris FastFire III
  • Burris FastFire 4
    • Burris FastFire IV
• Docter
• ADE RD3-001
• ADE RD3-002
• ADE RD3-009
• UTG Reflex Micro Dot
• Crimson Trace CTS-1200
• Crimson Trace CTS-1300
• Sightmark Mini Shot
• Sightmark Core Shot

The mounting screws require a 5/64" wrench and the set screws (when applicable) require a 1/16" wrench.

*All ADE mounts require 6-32 x 3/8" screws.

Please note: We have found that some red dots commonly found on Amazon such as the UTG and ADE may not hold the same tolerances as the red dots that this mount was initially created to work with. These dots may not fit properly on the posts on the plate. We would recommend either sending the red dot back for an exchange to whichever seller you purchased it from, or open up the holes in the bottom of the red dot to accommodate the pins.

EGW red dot mounts red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install.

Simply remove the rear sight on your gun and replace it with our mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. You can take our mount off and replace your rear sight at any time. Mounting hardware included.

Installation Instructions
- Remove the rear sight*
- Install the EGW Sight Mount in the dovetail
- Tighten set screw (if applicable)
- Place the red dot sight on the EGW Sight Mount
(placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.)
- Apply blue Loctite to the provided mounting screws
- Torque mounting screws to 15in/lbs

2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights
2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights

The screws that are included with this mount require a 5/64'' allen wrench for installation.

Modification of your firearm may nullify the manufacturer's warranty.
This product should be installed and checked by a qualified gunsmith.
No liability is expressed or implied for damage or injury which may result from improper installation or use of this product.

Alt Description:

• Remington R1 Red Dot Mount
• Para Elite RS Red Dot Mount
• Remington R1 Vortex Venom Mount
• Para Elite RS Vortex Venom Mount

The distinction between inferior quality and premium scope mount is undeniable. At MSP, we only offer gun accessories from the most trusted brands like Evolution Gun Works. Buy with confidence that we stand behind the product we sell.