My Cart: 0 item(s)
EGW Red Dot Mount for the Docter, Burris Fastfire, Vortex Venom, and Vortex Viper for S&W M&P Shield EZ
Mounting hardware is included.
This mount fits:
- S&W M&P Shield EZ .380 ACP
- S&W M&P Shield EZ 9mm
This mount does not fits:
- S&W M&P
- S&W M&P 2.0
- S&W M&P 22
We do not include the screw that fastens the adapter plate down to the slide. You must reuse the screw that came out of your gun. The screw is installed from the bottom of our slide and threads in to our adapter plate. You can see how the rear sight is uninstalled in this video.
Material: 7075 Aluminum
Coating: Matte Black Hardcoat
Overall Length: 1.811"
Overall Width: .99"
Torque Specs: 15 in/lbs
Mounting Hardware:
(2) 6-32 Button Head Screws
(2) 6-32 Flat Head Screws
Red Dot Fitment:
- Vortex Viper
- Vortex Venom
- Burris FastFire
- Docter
- ADE RD3-001
- ADE RD3-002
- ADE RD3-009
- UTG Reflex Micro Dot
- Crimson Trace CTS-1200
- Crimson Trace CTS-1300
- Sightmark Mini Shot
- Sightmark Core Shot
The mounting screws require a 5/64" wrench and the set screws (when applicable) require a 1/16" wrench.
*All ADE mounts require 6-32 x 3/8" screws.
Please note: We have found that some red dots commonly found on Amazon such as the UTG and ADE may not hold the same tolerances as the red dots that this mount was initially created to work with. These dots may not fit properly on the posts on the plate. We would recommend either sending the red dot back for an exchange to whichever seller you purchased it from, or open up the holes in the bottom of the red dot to accommodate the pins.
EGW red dot mounts red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install.
Simply remove the rear sight on your gun and replace it with our mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. You can take our mount off and replace your rear sight at any time. Mounting hardware included.
Installation Instructions
- Remove the rear sight*
- Install the EGW Sight Mount in the dovetail
- Tighten set screw (if applicable)
- Place the red dot sight on the EGW Sight Mount
(placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.)
- Apply blue Loctite to the provided mounting screws
- Torque mounting screws to 15in/lbs
2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights
2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights
The screws that are included with this mount require a 5/64'' allen wrench for installation.
Modification of your firearm may nullify the manufacturer's warranty.
This product should be installed and checked by a qualified gunsmith.
No liability is expressed or implied for damage or injury which may result from improper installation or use of this product.
M&P Shield Links
- m&p shield 9mm upgrades
- m&p shield 9mm accessories
- m&p shield plus accessories
- m&p 380 shield ez accessories
- s&w shield 40 accessories
- m&p shield upgrades
- m&p shield 2.0 upgrades
- smith and wesson m&p shield 9mm accessories
- m&p shield ez 9mm upgrades
- m&p shield 2.0 accessories
- m&p shield sights
- m&p shield holster
- speed loader 9mm
The distinction between inferior quality and premium M&P Shield Mount is undeniable. At MSP, we only offer MP Shield Accessories from the most trusted brands like Evolution Gun Works. Buy with confidence that we stand behind the product we sell.
WARNING: This product can expose you to Lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to - www.P65Warnings.ca.gov.
Customer Ratings & Reviews
Be the first to rate this item!
Write Review
