My Cart: 0 item(s)

EGW Remington 1100/1170/1187 Picatinny Rail Scope Mount
Description
Machined from: Domestic 6061 T6 Extruded Aluminum
Finish: Matte Black
Hardware: Hex head screws and wrench provided
Overall Length: 5.488"
Please review the following specs to make sure this is the mount for you:
Type of Mount: Remington 1100 / 1170 / 1187
Center Spread: 1.48 Overall Length of Mount: 5.48
*The center spread is the distance between the two middle holes, center to center, on your receiver.
This base sits at approximately 0.4 high.
Picatinny cross slots run the full length of the rail, which gives the shooter flexibility when mounting scope rings and other accessories.
The channel in the center reduces the overall mass of the mount, weighing in at 2-3oz on average.
Also, in many cases, it will not obstruct usage of factory iron sights.
EGWs one piece scope mounts are the obvious choice for hunters and tactical shooters alike.
This Evolution Gun Works (EGW) mount is a Picatinny-style base and compatible with Picatinny or Weaver scope rings.
Add EGWs Practical or HD Scope Rings to make it a complete overhaul!
We machine these in our shop using one of our USA-made Fadal machining centers.
After machining, the mounts are tumbled, sand blasted, and Type II anodized for long lasting durability.
The entire mount and accessories (from the mounting screws and wrench down to the packaging) are made in the USA.
Installation: EGW recommends 20 inch lbs of torque and a drip of blue loctite (loctite is available through our website and is sold separately).
Finish: Matte Black
Hardware: Hex head screws and wrench provided
Overall Length: 5.488"
Please review the following specs to make sure this is the mount for you:
Type of Mount: Remington 1100 / 1170 / 1187
Center Spread: 1.48 Overall Length of Mount: 5.48
*The center spread is the distance between the two middle holes, center to center, on your receiver.
This base sits at approximately 0.4 high.
Picatinny cross slots run the full length of the rail, which gives the shooter flexibility when mounting scope rings and other accessories.
The channel in the center reduces the overall mass of the mount, weighing in at 2-3oz on average.
Also, in many cases, it will not obstruct usage of factory iron sights.
EGWs one piece scope mounts are the obvious choice for hunters and tactical shooters alike.
This Evolution Gun Works (EGW) mount is a Picatinny-style base and compatible with Picatinny or Weaver scope rings.
Add EGWs Practical or HD Scope Rings to make it a complete overhaul!
We machine these in our shop using one of our USA-made Fadal machining centers.
After machining, the mounts are tumbled, sand blasted, and Type II anodized for long lasting durability.
The entire mount and accessories (from the mounting screws and wrench down to the packaging) are made in the USA.
Installation: EGW recommends 20 inch lbs of torque and a drip of blue loctite (loctite is available through our website and is sold separately).
Customer Ratings & Reviews
Ratings Snapshot
out of 5
5
(2)
4
(0)
3
(0)
2
(0)
1
(0)
Would recommend this product.
100%
out of 5
5
(2)
4
(0)
3
(0)
2
(0)
1
(0)
Would recommend this product.
100%
2 Total Reviews
- 1
a good Remington 1100 scope mount
Ajax
Location:
Date:
November 5, 2019
This Picatinny rail works as advertised. The rigidity of the rail will probably depend more on the installation, rather than the rail itself. Mounted on a Remington 1100 with Aimpoint Micro attached. Solid as a rock, no scratches on the finish as of yet. Approved!
Recommended
Shotgun Picatinny Rail Scope Mount
WY
Location:
Date:
July 31, 2019
A simple rail that allows you to mount most any optic on your shotgun. You can pay more and get a higher grade material, but realistically this will never fail, and the precision/alignment is more than adequate for it's intended purpose.
Recommended
2 Total Reviews
- 1