My Cart: 0 item(s)

Every Shot Counts - Shipping Starts at 5.95
Product Search

Secure Checkout
Uncle Mike's Sling Swivel Studs for Wood and Synthetic Stocks and Forend
    Uncle Mike's Sling Swivel Studs for Wood and Synthetic Stocks and Forend
    Purchase Uncle Mike's Sling Swivel Studs for Wood and Synthetic Stocks and Forend
    • Uncle Mike's Sling Swivel Studs for Wood and Synthetic Stocks and Forend
      Ratings Snapshot
      5.0
      out of 5
      5 (11)
      4 (0)
      3 (0)
      2 (0)
      1 (0)
      Would recommend this product.
      100%
      SKU: 100-UM-25200
      UPC: 043699252008
      Manufacturer: Uncle Mike's

    • MSRP: $3.45
      $2.83

      1 available for immediate delivery

      Quantity in Basket:  None

    •  

    Uncle Mike's Sling Swivel Studs for Wood and Synthetic Stocks and Forends, Blued

    Set of one each of 1/2" wood screw fore
    end base and 3/4" rear wood screw base
    with white spacers only.

    Set No. 2520-0

    WARNING: This product can expose you to Lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to - www.P65Warnings.ca.gov.

    Customer Ratings & Reviews

    11
    Ratings Snapshot
    5.0
    out of 5
    5 (11)
    4 (0)
    3 (0)
    2 (0)
    1 (0)
    Would recommend this product.
    100%
    5.0
    out of 5
    5 (11)
    4 (0)
    3 (0)
    2 (0)
    1 (0)
    Would recommend this product.
    100%
    11 Total Reviews
    • 1

    Exactly as shown. It's the sling swivel stud standard for a reason.

    5 out of 5
    Location:
    Date: March 4, 2023

    I recently acquired a laminated stock from E.A. Brown to pair with my Ruger 10/22. As the stock didn't come with any sling studs, I needed to purchase one to attach my folding bipod. I managed to find two studs for just $4. While the installation process wasn't too challenging, it did require some tinkering. Firstly, I drilled a pilot hole that was the same diameter as the shank of the stud, the full length of the stud. However, I noticed that when I began to screw in the stud, it started to chip and crack the surface of the stock. To prevent any further damage, I stopped and then drilled a 1/8" countersink hole, which was the diameter of the threads. After doing so, I started the stud again and this time, everything went smoothly. The washer space and the top of the stud managed to conceal the minor chipping that occurred initially, and the bipod attached effortlessly, looking great in the process.

    Recommended

    perfect for 10/22 wood or synthetic stock

    5 out of 5
    Location:
    Date: March 4, 2023

    I utilized this swivel screw to successfully attach a bipod to my synthetic 10/22 stock, and it is an excellent product. To do so, I drilled a slightly smaller hole and inserted a small piece of PVC into the skeleton of the synthetic stock. I then carefully threaded the swivel screw in and tightened it up perfectly. I am thrilled with the results. As I opted for the 3/4 inch size, I still have the 1/2 inch one for future use.

    Recommended

    simple to install

    5 out of 5
    Location:
    Date: March 4, 2023

    After the sling mount on my crossbow broke, I found the ideal solution in this sling stud. First, I removed the old mount and smoothed it out. Then, I created a pilot hole and easily screwed the new stud into the plastic injection-molded stock. A helpful tip is to use a drill bit that fits snugly into the stud hole to ensure the correct size. This drill bit can also be used to turn the stud into the stock with care, making sure not to force it and risk breakage.

    Recommended

    Uncle Mike's Sling Swivel Stud 115 RGS Set

    5 out of 5
    Location:
    Date: January 4, 2023

    The Uncle Mike's Sling Swivel Stud 115 RGS Set is a great product that works perfectly. I would definitely buy it again. It's important to use the correct size pilot bit and to cover the drilling area with masking tape to prevent splintering around the hole. Overall, I'm very satisfied with this purchase.

    Recommended

    sling studs for synthetic stock

    5 out of 5
    Location:
    Date: December 12, 2019

    This sling studs for the synthetic stock was straightforward to use, but the instructions seemed off on one of the holes. It was a little loose, and I had to add glue to hold it in, so I would use a smaller bit than instructed. These were put on an early Ruger 10-22, which did not have sling studs. I chose these without the swivels because the sling I chose had them. They were cheap and easy to use and had a professional look when done

    Recommended

    uncle mike's sling swivel studs

    5 out of 5
    Location:
    Date: December 12, 2019

    I installed one of these in a wooden stock as it was intended, no even there, and I installed the other in the LMT stock on an M4A1. Both are holding, and I don't imagine one can ask any more from such an item.

    Recommended

    sling swivel stud synthetic stock

    5 out of 5
    Location:
    Date: December 12, 2019

    You need two (2) different size drill bits, or you can buy a particular bit from UM. I just used two drill bits I had in the garage. It would be best to use a drill press, so you get the stud mounded straight, but you can do a fair job with a hand drill. The sling swivel stud synthetic stock come with instructions, but again, you need to pay attention and make sure you drill straight up & down, and not at an angle to the stock. You might get the location/center-right, but the stud needs to go in straight! It's not hard but pays attention.

    Recommended

    Sling studs for wood stock

    5 out of 5
    Location:
    Date: December 12, 2019

    I used these two swivel studs in an unorthodox way. Since I lost one screw for a rear wooden stock, the longer screw was applied there. For the shorter screw, I installed it at the 6 o'clock forward position of my DPMS LR-308 free float tube. I started with a smaller drill bit very slowly to not have it slide all over the tube and scratch it up. Using a punch tool was not an option as I did not want to risk bending the free-float tube. I worked my way up one more bit size to allow it to be a tight fit into the tube. It was only possible with these COARSE threads, not the FINE threaded screws out there. Upon setting the screw, I added a small goop of gorilla glue to the inside for extra measure. The reason I didn't use loc-tite was I didn't want to chance me ruining the threads. It had just 'tapped' on its own by me backing it out. I don't plan on removing it, it's intended for a harris bipod, I have a sling attached to the bipod, and it has not wiggled loose. It has stayed in place since summer of 2009.

    Recommended

    Excellent for adding sling mounts

    5 out of 5
    Location:
    Date: September 6, 2019

    These Sling Swivel Studs are Excellent for adding sling mounts to the rifle stock that didn't have them originally. Tip: drill a pilot about 1/2 the screw diameter to avoid splitting the wood and lubricate the threads with a bar of soap. Countersinking the hole with a larger drill finished the job. I've chosen not to use the fiber washer as they have a tendency to split over time.

    Recommended

    Excellent quality and low price.

    5 out of 5
    Location:
    Date: August 1, 2019

    Excellent quality and low price. I bought this to mount a bipod on a 10-22 and worked like a charm. I bought four more for future use for slings or bipod. This kit also comes with white spacers that I think add just a touch of class to a beautiful wood stock.

    Recommended

    effective upgrade.

    5 out of 5
    Location:
    Date: June 20, 2019

    Great for adding sling mounts to the beast that didn't have them initially. Make sure to drill a pilot about 1/2 the screw diameter to avoid splitting the wood. An old carpenter trick is to lubricate the threads with a bar of soap. Countersinking the hole with a larger drill finished the job. I've chosen not to use the fiber washer as they tend to split over time. I tried to find a picture of one that I did and can't tell the difference between the factory mounts and these.

    Recommended
    11 Total Reviews
    • 1


    Related Products