Burris AR-P.E.P.R. 1" Mount w/ Picatinny Top

10

| Write a Review

Ratings Snapshot

5.0

out of 5

5 (10)

4 (0)

3 (0)

2 (0)

1 (0)

Would recommend this product.

100%

SKU: 126-BUR-410343
UPC: 000381103420
Manufacturer: Burris

I bought this AR15 Scope mount over some of the cheaper ones because I was told that if you want a quality product that this was the way to go so I opted for a more expensive scope mount. It is very sturdy and constructed well and so far has been worth every bit of the money I spent on it. I own a Core 15 GTO AR-16 that came standard with the front sight post I wanted to retain my sights as well as being able to have some type of optic on my rifle how ever the front sight post blocks all optics that are mounted to the rail on the receiver I did not want to spend the money to have to buy quality fold down sights, then a gas block, and then pay someone to install them for me or pay for the gun smithing tools to make a one time modification that would remain permanent for the foreseeable future. After doing some research into my need and talking to a friend of mine who owns this mount and uses it on with his AR I decided to bite the bullet and give it a shot, I has some concerns because if you look at how the scope mount lines up on the rifle the scope would be pointing face first into the front sight post, I was assured that this would not be a problem and that the scope would see through the sight post and it would not interfere with the scope picture. This is 100% correct I have no problem with this scope mount and as far as I'm concerned this is the best product on the market, it is more expensive than its counter parts but I can assure you that the product is well worth the money that you spend

I have several AR 15 rifles. The Burris AR-pepr mount has been my favorite by far. The height is perfect, the mount seems to be very well made and the cantilever puts the eye relief right in the sweet spot. I am getting ready to order my third.

I purchased a 1" and a 30mm dia. Burris AR PEPR scope mounts to accommodate a Burris and Vortex scope for my AR rifles. Both scope mounts fit perfectly, and I was able to sight in within 4-5 shots. The Burris scope mount also allowed me to install a Caldwell brass catcher base mount just before the charging handle (back end of upper receiver Picatinny rail). With six screws per ring (12 screws total) I doubt this will ever come loose. The height of the mount is perfect for mounting a scope on a AR format rifle.

I purchased a 30mm version of this Burris AR pepr mount for an AR15 for use with a Leupold VX-R. Even though it is made in China, I decided to try it out. The mount is well designed and has an excellent finish and fit. The sight height is excellent, and cantilever put it in a very intuitive position. All of this would be great if the scope mounting bore were parallel to the base. It puts the point of impact 6" low at 18 yards after my elevation is maxed out. I'm almost out of windage also but was able to get the point of impact centered.

This Scope base installed very quickly on my Armalite - the adjustments to make sure the QD holds tight to the base are precise and easy, took less than 3 minutes. I installed a weaver scope and took the rifle to the field to sight in. Took the scope off and shot with a red dot for a while and re-installed the scope - shot in precisely the same spot as before - no problems what so ever. I would highly recommend the Burris ar-pepr mount.

Just put on my Burris AR PEPR 1" scope mount. The cantilever design allows you to mount it entirely to the upper receiver. Other mounts may require you to use your free float rail as well. If the upper receiver and the free float rail are not perfectly aligned or they shift relative to each other for any reason, you may have issues sighting in your scope. This is not detailed in the description, but it does come with the smooth ring tops like the quick-detach version that is $20 more. Aluminum construction, but still very solid. The two locking nuts could be a bit lower profile, but it is not so apparent once everything is mounted. They are reasonably priced too. I bought it based on the two recommendations on

The Burris AR-p.e.p.r Very well made mount puts scope out to a position where eye relief is perfect. Mounted the new Maglite XL200 (173 lumens) using Weaver 1" High Matt rings. This set up works well out to 100 yards and beyond in total darkness. A high quality/durable set up and looks good too.

The Burris AR Pepr very well constructed scope mount, sits my Leupold mark ar as close to my Magpul buis as you can get wt out touching. The rails are nice for mounting reflex sights, lasers, or anti cant devices. The only way it could be better is if it had the throw lever set up, but for the price, i have no problem using a screw driver. the truth is once you mount a scope, you really don't go back to irons unless you have to, but even if you disagree i don't think its worth spending double the money to take a $2 screw driver or socket out of the picture. gave it five stars because it does what it should and looks good doing it.

I bought the permanent mount for a flat top AR. Put the scope in the perfect forward position with a notch to spare. A surprise was the extra set of top halves without the mini rail. I went with the rail tops for a sexier look. The three screws per side give it a brutish and tactical look. I also liked that the nuts on the rail clamp are hex instead of knurled. I considered buying the quick detach version, but I'm glad I didn't. Very happy with the purchase.

I bought the 1" rings / permanent mount for a more secure reason. It is "Proper Eye Position Ready." I paired it with a Bushnell AR Optics 4.5x18x40mm scope. I'm happy... (not recommended for light-weight applications)