Mosin Nagant 9130 See-Thru Scout Scope Mount by Brass Stacker

Mosin Nagant 9130 See-Thru Scout Scope Mount by Brass Stacker

Mosin Nagant 9130 See-Thru Scout Scope Mount by Brass Stacker

Scope your Mosin while preserving its historic integrity.

Steel Picatinny Rail, Mounts Over Rear Sight Block

***PLEASE READ SPECIFICATIONS & FITMENT NOTES BEFORE PURCHASING***

There is no need for bent bolt handle with this Mount.

FEATURES: Allows for mounting of Scout Scope or other long eye relief optics on your military surplus Mosin Nagant model 91/30 and 91/59 without the need to drill & tap receiver or make any permanent modifications to the firearm. It is designed to fit over rear sight block in order to allow for continued use of the original fixed/iron sights up to 100 meters. The Mount is rigid steel construction with Black Oxide finish. 100% Lifetime Warranty!

Fits: Russian/Soviet M9130

 

 

SPECIFICATIONS: The Mount will accommodate a front to back (horizontal) pin center distance of 1.39" (35.3mm) to 1.82" (46.7mm) and allows for .039" (1mm) of up and down (vertical) movement. The Mount is designed to fit over rear sight blocks that measure between .750"(19.05mm) and .787"(20.00mm) wide. The total weight including hardware is 5.5 oz. We have made every reasonable effort to ensure that this product will fit the majority of M9130's. However, due to the large number of these firearms produced over many years around the world, it is impossible for us to allow for all manufacturing variation. Proper tightening of all hardware should result in no movement of the mount during normal firing recoil. If for any reason our Mount does not work with your specific 9130 it can be returned (undamaged) for a full refund.

UNIT:

  • Mount: CNC laser cut perimeter, die punched holes and mounting slots, form tapped threads and die press formed. 3/32" (13 ga.) thick HR, P&O type CS-B A569 carbon steel; 40000 psi yield strength. Black Oxide plated.
  • Picatinny Rail: CNC machined to MIL-STD-1913. 8" long. HR ATSM A36 low carbon steel; 36000 psi yield strength. Black Oxide plated.
  • Screws: #10-32 x ¼" flat head socket cap screws. Alloy steel; Rc 38-45 hardness.

HARDWARE:

  • Bolts: M3x.5 X 30mm socket head cap screw. Grade 12.9 medium carbon Q&T alloy steel; Rc 38-44 hardness; 160000 psi yield strength, 177000 psi tensile strength; 1.67 ft lbs tightening torque.
  • Nuts: M3x.5 Hex Nut. Grade 2 low carbon steel; Rc 32 hardness; 60000 psi tensile strength. Black Oxide plated.
  • Lock Washers: 3mm cut spring lock washer. Steel. Black Oxide plated.
  • Flat Washers: 3mm plain flat washer. Steel. Black Oxide plated

TOOLS PROVIDED:

Wrench: 2.5mm short arm hex key. Steel.

  • Drill: 3.00x41x70mm HSS Jobber. *Note: Drill is provided as a means to clean out or straighten existing pin holes.*
  • Punch: 3/32" x 7/8" dowel pin. Hardened 4140 alloy steel; Rc 47. ¼" x 2" Aluminum handle. *Note: This punch is not designed to be used on difficult to remove pins such as those soldered in place.*
  • Complete installation instructions are supplied.

SCOPE & RINGS ARE NOT PROVIDED!

 

FITMENT NOTES:

This mount will NOT work for an M38/M44/T53! See Model MN384453SSM for a M38/M44/T53.

The pin holes in the rear sight block are often located inconsistently as a result of the original manufacturing process. The two holes are frequently not parallel to each other and may be out of alignment or skewed. The mount can only accomodate so much of this misalignment. You should measure the center distances from pin to pin on both sides and check those with the dimensions listed in the SPECIFICATIONS to ensure that the mount will fit properly. A 3mm drill is provided and can be used to clean out and straighten (to some degree) without enlarging the pins holes once the pins are removed. The pin holes for the rear sight block are generally .118"(3.0mm) in diameter and the supplied 3mm bolts have a nominal OD of .115"(2.92mm). This tight fit along with the use of an appropriate liquid thread locker for the screws and nuts, as well as proper tightening of the same should result in no movement of the Mount during normal firing recoil. Occasionally the rear sight block itself, as it sits on the barrel dovetail underneath, can be out of alignment with the bore axis. This condition, if extreme, can adversely effect how the Mount sits. Please note that some rifles may have pins holding the rear sight block to the barrel soldered in place. Instructions for correctly applying the required heat to remove the solder are provided for use at consumer’s discretion. Also, some may have pins that require the use of substantial force to remove. This should be done with a heavy duty punch (not supplied). The supplied light duty punch is NOT designed for difficult to remove pins.

Please refer to mount “Specifications” to determine the acceptable amount of deviation for the conditions listed below. IMPORTANT! If your rifle has a condition as described below that will not allow the MN9130SSM Mount to work... please see the MN39SSMR Universal Fit Anchor Point Series mount.

FIGURE 1) A single pin holding the rear sight block to the barrel will not allow the MN9130SSM mount to attach properly. **The mount can be used as a template to drill a second hole with the supplied drill bit at consumer’s discretion.
FIGURE 2) Pins not perpendicular or skewed to bore centerline can result in the MN9130SSM mount not fitting properly.
FIGURE 3) Pins not the same distance from bore centerline can result in an unacceptable degree of up or down “Pitch” making the MN9130SSM mount hard to level front to back.
FIGURE 4) A rear sight block that does not run parallel with bore centerline can result in an unacceptable degree of right or left “Yaw” making the MN9130SSM mount lead off to one side.
FIGURE 5) Pins higher on one side from bore centerline than the other side can result in an unacceptable degree of “Roll” making the MN9130SSM mount hard to level side to side.

some text

TOOLS REQUIRED:

Safety glasses, heavy gloves, solid work surface or vise, hammer, flat blade screw driver, 7/32" (5.5mm) socket driver or wrench, hand drill, and liquid thread locker. A MAPP (Methyl Acetylene Propadience Propane) gas torch and heavy duty punch may be required to remove existing pins from the rear sight block if they are soldered in place. You can usually find these items at your local hardware or plumbers supply. The application of heat, if done properly, will not cause damage. Keep in mind that you only need to reach the melting point of the solder and that this same temperature was achieved during original construction without adverse effects. Procedure provided in supplied instructions.

NOTE:

As with ANY scope on ANY mount, should it receive an impact (dropped, hit, etc.) it should not be trusted to be accurate. Thus the SEE-THRU feature of our Mount. You can always still use the original iron or open sights if you feel the Mount has been compromised. Design subject to change without prior notice.

Caution! Improper installation or use may result in damage to property, severe injury, or loss of life. If for any reason this product does not function properly, discontinue use immediately. Always practice proper SAFETY & ensure an UNLOADED condition before beginning installation.

 

(average out of 192 votes: 3.2 stars)
MSP Code: 151-TGR-MN-SSM
Price: $59.00

Status: Status: In Stock, ready to ship
(average out of 192 votes: 3.2 stars)


You May Also Like
©2013 Mounting Solutions Plus Inc. All Rights Reserved. Phone: